Rust Bullet

What is the recommended method of Application for Marine use?

An airless spray system using a 517 or a 519 tip at 2500 PSI pressure is the suggested method for Industrial, Marine or Military applications. Three generous coats, properly applied, will achieve the total dry film thickness (dft) of 12 mils as required for surface protection under the 10 year warranty. It is recommended that before and after each coat of Rust Bullet is applied; the pump, lines, and sprayer be flushed with Xylene. It is essential to keep the application equipment clean and the line free of any Rust Bullet product. Acetone may be substituted if Xylene is unavailable.

Are there recommendations on Media Blasting?

Soda Blasting and Dry Ice Blasting are two methods of media blasting that are effective, clean, and environmentally safe. Both media are sound options and clean up will be relatively minor including the drying procedure after the dry ice blasting.

Is it necessary to remove surface paint prior to applying Rust Bullet?

The removal of existing surface paint prior to Rust Bullet application will depend on the condition and type of paint on the surface. To achieve maximum adhesion, it is always recommended to remove any old paint or coating before applying Rust Bullet.

Do I Apply Rust Bullet only where Rust is Apparent?

Rust Bullet is designed to protect rusted and clean metal. It is always advantageous to protect metal, even when there are no visible signs of corrosion. If Rust Bullet is applied only in the rusted areas, it will stop the rust on that surface area, but the uncoated area will be left unprotected. Remember, if it's made or iron or steel, it will rust and corrode if left unprotected.

Are additional coats of Rust Bullet required for Marine Applications?

As Rust Bullet cures it releases carbon dioxide gas while dehydrating the rust. This process of "gassing off" (expelling solvents) may create small pin holes in the first coat of Rust Bullet. A generous initial coat of Rust Bullet will penetrate the rust down to the original metal surface while the second and any successive coats seal these tiny pin holes, forming an air tight, armor like shield over the application surface. If these pin holes are not sealed after the first coat, air and moisture may penetrate the Rust Bullet, allowing rust and corrosion to form.

Is there a recommendation of the number of coatings for a ship submerged in Sea Water and what is the effect of salt water on Rust Bullet?

Three generous coats would be the minimum recommended. If the ship will be used to do a lot of hard docking or hard landing on the beach then four coats will provided more adequate protection. Sea temperatures vary as does the salt content and these factors may affect the recommended dft. Salt water should have no effect on Rust Bullet unless the water temperature is rapidly changed from sub zeros to a couple of hundred degrees Fahrenheit. If the Rust Bullet coating is applied properly from preparation to the end, the coating will not peel or bubbling off. Unless there are unexpected chemicals concentrated where the hull is submerged, the Rust Bullet coating should hold its ground with ease. Should there be an event, such as a boating accident and the coating integrity is compromised, after inspection and evaluation, you can always re-apply the Rust Bullet to the comprised area.

Does Rust Bullet recommend the use of antifouling paint?

Rust Bullet provides durable surface protection that is scratch, chip, chemical, and UV resistant. Antifouling bottom paints reduce or eliminate marine growth that develops on a boat's underwater surface. Antifouling paints do this by using biocides (chemicals) that slowly release to repel underwater aquatic life. Most antifouling paints require a chemical reaction with the surface to which it is applied for proper adhesion. This reaction does not occur when applied over Rust Bullet as Rust Bullet is virtually impenetrable. If you do use antifouling paint, scuffing up the Rust Bullet surface along with the use of an etching primer may be necessary. Only use antifouling paint that is compatible with an aluminum hull; that's virtually what you end up with when a surface is protected with Rust Bullet. Always check with the antifouling paint’s manufacturer before applying an antifouling paint over Rust Bullet.

Is Rust Bullet advised for use on Gasoline Tanks?

Rust Bullet is not affected by gas itself; Rust Bullet was not and is not designed as a tank sealer for the inside of a non-commercial small gasoline tank we do not have an official recommendation on this application. Rust Bullet has not been tested for application inside this type of gasoline tank therefore we extend no warranty or guarantee.

Can Rust Bullet be applied to an Aluminum Hull?

Yes you can Apply Rust Bullet directly to the clean surface of an Aluminum Hull.

Will Rust Bullet reduce the growth of Marine Organisms?

Based on the chemistry of Rust Bullet it is inhospitable to marine organisms. Marine organisms require several conditions to survive; such as sun light, suitable temperature range and a host surface on which to colonize. Additionally, these organisms capture energy from the sun in the bonds of carbon-based molecules through a process called photosynthesis. Rust Bullet has exceptional chemical resistance and forms an armor shield like coating. This shield should prevent any colonization of Autotrophs, such as algae, plants, and some bacteria; however, we cannot say Rust Bullet will stop the growth of marine organism forever, as there are many other factors involved. Such as the ship's location, length of period at harbor, and travel locations to name a few. An antifouling paint is still a very good application that will enhance the prevention of growth of the Autotrophs, as well as the benefit of additional protection to the ship's underside.

Does diesel fuel degrade Rust Bullet?

Rust Bullet will hold up to #2 Diesel Fuel without issue.

What is the difference between Rust Bullet standard formula (Gold Label) and Rust Bullet Automotive formula (Silver Label)?

Both Rust Bullet and Rust Bullet Automotive are industrial strength protective coatings. They have the same patented anti-corrosive properties and will out perform any other rust inhibitive, protective coating on the market. Rust Bullet Automotive is formulated a bit thinner than the Rust Bullet standard formula to easily flow through an HVLP auto finishing spray system. Rust Bullet Automotive has more metal and will produce a smoother finish typically desired for automotive projects.

Do I Apply Rust Bullet only where Rust is Apparent?

The automobile industry uses steel in its manufacturing wherever structural strength is needed. Ideally this steel should be protected before it starts to rust and corrode; thus preserving the strength and integrity it was originally designed to provide. Rust Bullet not only kills existing rust, it seals and protects surfaces that have not yet started to rust providing years of prevention. If it is made of iron, metal, or steel, it will rust and corrode if left unprotected; start protecting your investment today.

Can I Apply Rust Bullet Automotive with a Brush?

All Rust Bullet Formulas may be applied by brush, roller, or spray equipment. A brush coat should be applied evenly without buildup in a cross hatch method (up and down and side to side). Even coats using the crosshatch application method will produce the best results. Always keep a wet edge on the tip of your paint brush. A two to three coat brush application generally achieves a dft (dry film thickness) of 6 mils. Roller applications result in an approximate dft of 3 mils per coat. An HVLP spray system applies approximately 2 mils, while the Airless sprayer application averages 3 to 4 mils per coat. One gallon of Rust Bullet or Rust Bullet Automotive covers approximately 200 sq.ft. with a finished dft of 6 mils.

How do I Apply Rust Bullet Automotive with an HVLP Spray System?

Rust Bullet Automotive applied through an HVLP spray system using a 1.5 tip with 40 PSI will achieve a dft of approximately 2 mils per coat. It is important to run Xylene through the spray equipment prior to spraying the first coat of Rust Bullet Automotive to remove any moisture that may be trapped in the equipment. After the application of each coat of Rust Bullet Automotive, flush the gun or submerge the tip in Xylene. It is important to keep the equipment and sprayer clean. If the spray gun has a filter, it must also be cleaned. Acetone may be used if Xylene is not available. Application equipment must be cleaned immediately after use to avoid damage.

Why Do I Need to Apply Multiple Coats of Rust Bullet?

Rust Bullet is a ONE STEP, TWO COAT product. As Rust Bullet cures it expels solvents and releases a carbon dioxide gas while dehydrating the rust. The first coat of Rust Bullet soaks through the rust down to the metal below, encapsulates the rust, and dehydrates it. The first coat must be applied generously enough over the rust for this process to take place. As the first coat dries and gases off, tiny pin holes may form in the coating. The second coat is critical to fill any pin holes and seal the surface with an air tight, armor like shield of protection. If the pin holes are not sealed after the first coat, air and moisture may penetrate the coating exposing the surface to further damage. Apply additional coats to achieve the desired dft for the appropriate protection for the project.

When Do I Apply the Next Coat of Rust Bullet?

Optimum drying time between coats of Rust Bullet is 2 to 4 hours. When the product does not transfer to a gloved finger tip it is ready to accept an additional coat of Rust Bullet. It is important that corners, edges, and heavily pitted areas are adequately covered. When Rust Bullet cures it pulls tight to the center; therefore, it is particularly important that edges and corners are sufficiently covered.

Can Rust Bullet be used as a Primer?

Rust Bullet can be used as an automotive primer and can be wet sanded and directly painted over. Before applying a finish color to a surface coated with Rust Bullet, we recommend wet sanding the surface with a very fine sand paper. This wet sanding may be achieved by using 100 to 150 grit sanding paper. Apply an additional coat of Rust Bullet, again wet sanding to a very smooth surface, wait 6 - 7 hours before applying a topcoat (time may vary depending on weather conditions).

Is Rust Bullet Compatible with Automotive Fillers, Fiberglass, and Primers?

Body fillers, premium automotive primers, and automotive paint may be applied over Rust Bullet. To insure proper adhesion, Rust Bullet should be sanded with a 100-150 grit sand paper before applying body fillers, fiberglass or premium primers. When working on body parts, Rust Bullet should be layered, i.e. apply two or three coats of Rust Bullet, apply the bondo or fiberglass, and then apply another coat of Rust Bullet. This will seal out any moisture the body filler might attract while adding strength and durability to any weak places. You can apply Rust Bullet over existing bondo, fiberglass, or paint if there is no rust present after scuffing the surface with 100 or 150 grit sand paper or sanding block. If bondo is applied directly to a rusted area it has a tendency to absorb moisture which will cause further rusting and bubbling in the bondo. Rust Bullet works best when it is in direct contact with the metal. The final coat of Rust Bullet should be wet sanded before the application of a top coat.

What should I do if I waited too long before applying the next coat of Rust Bullet?

Optimum drying time between coats of Rust Bullet is approximately two (2) to four (4) hours depending on humidity levels. If more than 72 hours have passed since the previous coat of Rust Bullet, the surface pores will have closed making it necessary to scuff up the surface with a 100 to 150 grit sanding block. Scuffing the surface will reopen the pores allowing Rust Bullet to successfully accept an additional coat of Rust Bullet or a top coat. Rust Bullet’s pores remain open and receptive to a top coat for approximately 24 to 72 hours after the application of the final coat of Rust Bullet. Once the pores have completed the gassing off while dehydrating the rusted areas, the pores will begin to close; this process generally takes 4 – 5 days. High humidity conditions may accelerate this process to 2 - 3 days.

What Steps are Required when Applying a Top Coat over Rust Bullet?

Ideally a topcoat should be applied within 24 to 48 hours after the final coat of Rust Bullet. It is necessary to allow enough time for the curing or gassing off process to complete. The application of a top coat before this process is complete may result in dimpling of the surface and an undesirable finish. If you are using a premium finishing paint and the manufacturer has specific primer requirements, it is recommended you apply the primer over Rust Bullet after the surface has been scuffed up and wet sanded. Rust Bullet is an excellent adhesion promoter and enhances the adhesive properties of any topcoat you choose. A top coat is not necessary with Rust Bullet Automotive formula; however, a topcoat may be applied 24 hours after the final coat of Rust Bullet. If black is the finished color desired, Rust Bullet BlackShell™ is an excellent choice for a Gloss Black finish. BlackShell is specifically designed as the optimum topcoat for Rust Bullet or Rust Bullet Automotive. BlackShell is an outstanding protective stand alone coating that requires no base coat or topcoat and when applied over Rust Bullet provides unbeatable protection with a gloss black finish. Rust Bullet, or the exceptional combination of Rust Bullet top coated with BlackShell, are unsurpassed in rust, corrosion, and abrasion protection.

Is Rust Bullet advised for use on Gasoline Tanks?

Rust Bullet is not affected by gas itself. Rust Bullet was not and is not designed as a tank sealer on the inside of a tank. We have not tested for this application and can offer no promise as to what the outcome will be if used as such. Rust Bullet can be used on the exterior, but it was not designed for internal use on a gas tank.

Is Rust Bullet advised for use on an Exhaust System?

Rust Bullet can withstand a constant temperature of 315 degrees Fahrenheit with burst of up to 700 degrees Fahrenheit for short periods of time (approximately 24 hours). Rust Bullet provides excellent protection for most engine components; however, is not recommended for coating exhaust systems due to the excessive heat produced on headers, exhaust manifolds, catalytic converter or exhaust pipes.

Can I apply Rust Bullet under a Truck Bed Liner?

Rust Bullet provides excellent surface protection under bed liner material. Apply Rust Bullet according to the application guidelines. As with the addition of any topcoat or other product, if 72 hours have lapsed after the final coat of Rust Bullet, the surface should be scuffed with 100-150 grit sanding paper or sanding block to ensure proper adhesion of the liner material.

Does diesel fuel degrade Rust Bullet?

Rust Bullet will hold up to #2 Diesel Fuel without issue.

Will Rust Bullet Protect My Galvanized Metal Roof?

Rust Bullet is the ideal coating for protecting your sheet metal buildings and roofs; it not only provides protection from rust and corrosion, but will actually make your metal roof stronger and more weather resistant. Rust Bullet® sprays easily and quickly with the use of an airless spray gun. Costly replacements can be avoided by simply applying two coats of Rust Bullet. Refer to the Rust Bullet Home and Farm Page for more details.

Is Rust Bullet appropriate for Industrial and Commercial projects?

Rust Bullet provides superior protection even under the harsh conditions common of industrial and commercial environments. It defends surfaces with an impenetrable, nonporous; armor like shield that repairs, protects, and maintains surface integrity. Rust Bullet is scratch, chip, and chemical resistant and provides outstanding protection from abrasives and corrosives that damage and destroy surfaces. Rust Bullet is a one step; one product coating that can be applied with little or no surface preparation, reducing the cost of product, labor, and the containment of waste. Rust Bullet requires little or no maintenance, consequently saving money and minimizing down time. If surface preparation is necessary, Media Blasting is recommended for large commercial and industrial applications; common methods consist of baking powder, dry ice and hydro blasting. Rust Bullet Standard Formula (Gold Label) is appropriate for most industrial or commercial type projects. A minimum finished dry film thickness (dft) of 12 mils is recommended for most industrial and commercial applications. Rust Bullet is available at quantity discount pricing in Pints, Quarts, Gallons, 5 Gallon Pails, and 55 Gallon Drums.

What is Dry Film Thickness (dft)?

Dry Film Thickness (dft) is the thickness of a coating when dry, expressed in mils. A mil is a measurement used to determine the thickness of a coating. One mil equals one thousandth of an inch. 1 mil = .001 inch (1/1000). For comparison purposes, 4 mils is approximately the thickness of one sheet of standard paper. Many plastic trash bags have a thickness of about 1.0 mil although heavy duty (so-called "contractors") bags may be about 3.0 mils.

How do I know what the recommended dry film thickness (dft) is for my project?

The higher the mil measurement of Rust Bullet's dry film thickness (dft), the greater the protection provided. Generally industrial or commercial type projects require a minimum dft of 12 mils; however, many variables should be considered when determining the desired dft for any project. Some of these variables to consider are: 1. The existing condition of the surface being coated 2. The surface's exposure to: - Moisture - Harsh chemicals - Abrasive objects 3. The damaging effects the surface must endure from environmental conditions

Once I have determined the desired dry film thickness (dft) for my project, how do I ensure the finished project has sufficient mil coverage?

The most accurate way to measure dry film thickness is to use a mil gauge. It is critical that at least two coats of Rust Bullet be applied to achieve a dft of 6 mils. One coat of Rust Bullet Standard Formula (Gold Label) produces an approximate dry film thickness (dft) of 3 mils (0.003 inches or 0.076 millimeters). The first coat of Rust Bullet soaks through the rust down to the metal below, encapsulates the rust, and dehydrates it. The first coat must be applied generously enough over the rust for this process to take place. As the first coat dries and gases off, tiny pin holes form in the coating. The second coat will fill any pin holes and seal the surface. Apply additional coats to achieve the desired dft for the appropriate protection for the project. One gallon of Rust Bullet covers approximately 400 sq. ft. with a single coat for a dft of 3 mils, i.e. if the dry film thickness for a project is determined to be 12 mils; one gallon will cover approximately 100 sq. ft. The number of coats needed to achieve the appropriate dft will depend on the chosen method of application: brush, roller, HVLP Spray System, or Airless Spray System. For example, Rust Bullet® Automotive (Silver Label) is formulated a bit thinner than Rust Bullet® standard (Gold Label) to flow easily through an HVLP Spray System; therefore, additional coats may be required to achieve the desired dry film thickness.

Why must I stir Rust Bullet thoroughly before applying?

Rust Bullet uses only the finest raw materials available in the manufacturing of its coatings. Some of these ingredients may separate or settle at the bottom of the container. Rust Bullet must be stirred thoroughly before use to ensure the coating's consistency is uniform.

Can an Electric Paddle or other Mechanical Device be used to stir Rust Bullet?

No. Never stir the product by mechanical means; this will trap air molecules containing moisture between the coating and the surface causing improper curing and possible coating failure.

How does Rust Bullet compare to an Epoxy Primer?

An Epoxy Primer is not an anti-corrosive coating and will not furnish the protection provided by Rust Bullet. Rust Bullet coating penetrates and dehydrates rust then forms a protective shield that defends the surface against corrosion and abrasion for many years. If an epoxy finish is desired, and the existing surface is an epoxy finish, scrape off any loose rust and epoxy coating, rough-up the remaining tight epoxy with 100 3 grit sandpaper prior to applying Rust Bullet, then re-apply the epoxy coating over the final coat of Rust Bullet. Please note: For best results, the surface should be prepared down to bare metal. Rust Bullet works best when it is in direct contact with rusted or clean metal.

How does Rust Bullet compare to an Epoxy as a Bridge Coating?

Rust Bullet provides excellent, long lasting, low maintenance protection for bridges and other transportation infrastructures. Rust Bullet is a high performance coating that has been awarded two (2) United States Patents for its two (2) unique technologies for rust and corrosion control. Generally Epoxy coatings are much thicker, plastic type coatings not intended to control corrosion. Epoxy coating applications are more complicated and labor intensive than Rust Bullet’s application. Other paints and coatings, including Epoxy coatings, require extensive preparation using a variety of techniques such as, sand blasting and collecting, needling, heavy scraping and chemical treating. Added to the high cost for these preparation procedures, costs for the containment and disposal of the waste created by these extensive preparation procedures, in order to comply with EPA (Environmental Protection Agency) requirements, often make these costs far greater than the initial cost of the product. None of these extensive preparation procedures are needed for Rust Bullet, consequently saving down time, labor, and cost. An Epoxy topcoat can be applied if desired.

Will Rust Bullet protect my Galvanized Metal Roof?

Rust Bullet is the ideal coating for protecting your sheet metal buildings and roofs. It not only provides protection from rust and corrosion, but will actually make your metal roof stronger and more weather resistant. Rust Bullet sprays easily and quickly with the use of an airless spray system. Costly replacements can be avoided by simply applying Rust Bullet.

What is the recommended application method for Galvanized Corrugated Roofs?

The recommended application method for Rust Bullet on Galvanized Corrugated Roof projects is an airless spray system with a 517/519 tip and 2400 PSI. Two or more coats should be applied depending on the desired dft (dry film thickness); each coat of Rust Bullet will add strength and durability to the metal roof. Please refer to our Application Guidelines for detailed instructions on airless spray systems.

Will Rust Bullet protect Concrete?

Concrete has been a reliable and versatile product for centuries. Chosen for its strength and durability, concrete is expected to withstand the most abusive conditions. It is subjected to the destructive effects from harsh chemical spills, abrasive objects, moisture, and the impact from heavy tools and machinery often resulting in an unsightly appearance and damage requiring costly repairs or replacement. Rust Bullet, with its Superior Patented Technology for rust and corrosion control, also provides outstanding protection to many other surfaces, including concrete. Rust Bullet protective coating will: 1. provide excellent chemical resistance 2. provide protection from abrasives 3. seal a surface from moisture 4. allow easy clean up of spills 5. prevent concrete from sweating 6. reduce dust 7. fill cracks, gaps, and chips 8. enhance appearance 9. add years of life to concrete surfaces Rust Bullet not only improves the appearance of concrete, it provides an impervious shield allowing easy clean up of oil, grease, and chemical spills along with strong protection against impact and abrasives. Power wash or simply rinse off dirt and debris and let the surface dry completely before applying Rust Bullet. Two to three coats of Rust Bullet is usually sufficient for most concrete applications depending on the concrete's condition and existing damage. Rust Bullet is self leveling and can fill in cracks, gaps, and chips up to ¼ inch. If a slip resistant surface is desired, sprinkle silica or similar fine sand over a tacky coat of Rust Bullet, allow just enough time for the sand to adhere, and then apply the final coat of Rust Bullet.

Can Rust Bullet be used for Wrought Iron Fencing, Furniture, and Fixtures?

Rust Bullet Standard Formula (Gold Label) will provide superior protection from corrosion and abrasives to wrought iron fencing, furniture, and fixtures, adding years of life to the integrity of the steel. Prior to applying Rust Bullet, simply wire brush the rusted areas to remove loose or flaking rust; wash off any dirt and dust or oil film and let the surface dry completely. The best methods of application for wrought iron are a Close Nap Roller or an Airless Spray System; paint brush application will also work. Less expensive sprayers, such as a Wagner Power Sprayer, can be purchased for home use. Prior to using spray equipment, be sure to run Xylene or Toluene through the equipment to remove any moisture. Please see our Application Information and Guidelines for more detailed information on spray application. If black is the desired finished color for the wrought iron, use Rust Bullet BlackShell as a topcoat. BlackShell is formulated with specialized resins and anticorrosive agents and can be used as a stand alone anticorrosive coating that will protect iron and steel. Although BlackShell will easily out-perform other protective coatings, it will not produce the level of protection of the patented Rust Bullet standard or Rust Bullet Automotive formulas for fighting rust and corrosion. For a black finish with the absolute best rust and corrosion protection, apply BlackShell over Rust Bullet® standard or Rust Bullet® Automotive.

Is Rust Bullet recommended for use on a Chain-Link Fence?

Known for its strength and durability, chain-link is perhaps the most economical type of fencing available. Commercial chain-link fence systems have been preferred for decades to define property lines and enclose government and business facilities, adding protection, security, and value to commercial property. Fence manufacturers make products for many different uses including lightweight, temporary needs. The application of Inferior coatings may allow the components to rust prematurely. The result is a permanent installation made from materials that weren't designed for longevity. The protective coating will fail much sooner than loss of steel integrity. Many manufacturers offer warranties that apply only to the loss of structural integrity of the steel, meaning the product has rusted to the point that the strength of the steel is no longer there. Rust Bullet Standard Formula (Gold Label) will provide superior protection from corrosion and abrasives to chain-link fencing adding years of life to the integrity of the steel. Prior to applying Rust Bullet, simply wire brush the rusted areas to remove loose or flaking rust; wash off dirt and dust and let fence dry completely. The best tool for application to the chain mesh is a long-nap paint roller with a 1 1/2-inch nap; the longer the nap the better because the roller's fibers will reach through and around the fence material. Ideally both sides of the fence can be coated at the same time with the assistance of a co-worker. A brush should be used on the fence rails, posts, hardware, and horizontal supports. If an airless spray system is used a 517 tip size is recommended. It is important that the area behind the fence be protected from overspray.

Will Rust Bullet protect metal and concrete from Magnesium Chloride?

Magnesium chloride is used as a de-icer or anti-icer in many states. Magnesium chloride is available in dry or liquid form; either form is very effective in melting ice. It has been confirmed that magnesium chloride will cause significant damage to concrete and metal. Magnesium chloride is very corrosive and will stick to any surface when dry and react with moisture or water to corrode metal and concrete. It will affect concrete in two ways, either by a slow rate or a fast attack depending on the concentration and the conditions and circumstances. Rust Bullet will perform well to protect metal and concrete from direct contact with magnesium chloride. A very high concentration of magnesium chloride on a frequent basis will reduce the protective properties of any corrosion control coating, including Rust Bullet. Rust Bullet with its armor tuff coating will last longer and provide better protection than any other product available. A dry film thickness (dft) of 12 -15 mils will provide much greater protection to the surface than applying a dft of only 6 - 8 mils.

Is Rust Bullet an appropriate coating for use on an Air Duct?

Rust Bullet will provide excellent protection for an Air Duct System. We recommend not running air through the system for 72 hours after the final coat of Rust Bullet has been applied. Rust Bullet will encapsulate the rusted areas adding strength to the coated surfaces.

Can Rust Bullet be used on Gasoline Tanks?

Rust Bullet is not affected by gas itself. Rust Bullet was not, and is not, designed as a tank sealer on the inside of a tank. We have not tested for this application and can offer no promise as to what the outcome will be if used as such. Rust Bullet can be used on the exterior, but it was not designed for internal use on a gas tank.

Does Rust Bullet contain Lead?

Rust Bullet Products contain no Lead, no Zinc, no Chromates, no Acids, and no Heavy Metals. Our Products comply with Volatile Organic Compound (VOC) limits regulated by The Environmental Protection Agency and the more stringent regulations of the State of California.

Will Fertilizer and Lime effect Rust Bullet?

When properly applied, Rust Bullet will hold up extremely well to fertilizer and lime. For best results apply thin even coats of Rust Bullet to achieve a dry film thickness (dft) of 12 mils.

How does Rust Bullet Hold up to Diesel Fuel?

Rust Bullet will hold up to diesel fuel No.2 with no adverse effects. Rust Bullet will provide a chemical bond to the metal and the topcoat when properly applied and used in the recommended timeline.

Can a surface coated with Rust Bullet be Welded?

To ensure the welded metals are properly bonded, the Rust Bullet coating should be removed to expose the bare metal. It is possible to join two Rust Bullet coated metals by welding without removing Rust Bullet; the metal will join together but may not achieve the strong bond expected by the welding process. If metal coated with Rust Bullet, or another coating, is welded without removing the existing coating, the extreme heat involved in the welding process will disintegrate the coating possibly releasing harmful gases; therefore, the appropriate safety precautions, such as wearing a gas mask and safety goggles, must be followed.

Is Rust Bullet compatible with Cadmium?

Rust Bullet is compatible with Cadmium. Cadmium is mostly used in the electroplating of metal and steel. It is used as a form of corrosion protection. Before applying Rust Bullet on electroplated surfaces, the surface must be clean and free of grease and wax.

Can Rust Bullet be used on Concrete or Steel Swimming Pools?

Rust Bullet will provide outstanding protection to a concrete or steel swimming pool. Apply two to three coats over the clean dry surface. There will not be any bleed through with the use of Rust Bullet and the surface will be sealed, protected and ready for the application of a new pool coating. We suggest using specialized spray-on pool liner paint after applying two to three coats of Rust Bullet. Rust Bullet will provide excellent protection to the concrete or steel and the pool liner paint will give the pool that natural blue color as well as stop any water penetration.

What if my project requires a faster recoat time? Do I have to wait the recommended 2 to 4 hours between coats?

Rust Bullet requires waiting 2 to 4 hours between coats; however, Rust Bullet Rapid Fire Accelerator can be added to the Rust Bullet Standard or Rust Bullet Automotive formulas to decrease the normal recoat time of 2 to 4 hrs to approximately 30 to 40 minutes per coat. Rapid Fire makes it possible to apply multiple coats of Rust Bullet in a single day and reduces project completion time by as much as 80%. A Rust Bullet coating accelerated with Rapid Fire can be applied with either an HVLP Spray System or an Airless Spray System. IMPORTANT: Rust Bullet Rapid Fire Accelerator is added to the Rust Bullet coating at the job site; it can not be added until you are ready for application. As soon as Rapid Fire has been added, the curing process begins. Pot time is approximately 6 hours. Only mix Rapid Fire Accelerator into the quantity of Rust Bullet that will be used within a 6 hr period.

When can I apply a Topcoat if I have coated my project with a Rust Bullet coating that has been accelerated with Rapid Fire?

After applying the final coat of Rust Bullet Standard or Rust Bullet Automotive that has been accelerated with Rapid Fire, wait approximately 24 hours before applying a Topcoat.

Will I have problems with the application of Rust Bullet if I am located in an area with High Humidity?

If humidity is too high (80% +), it will adversely affect the curing and adhesion process. A couple of things can be done to minimize the adverse affects of high humidity, if necessary: 1. Provide air circulation or an air flow that vents the air away from the coated surface. 2. Apply Rust Bullet by brush. A brush application tends to trap less air and moisture and is therefore the best application method in a high humidity zone. Apply additional, thinner coats rather than fewer, thicker coats. This will help eliminate the formation of bubbles or blisters on the coating surface which can occur if the co2 and solvents cannot be expelled. The formation of humidity bubbles or blisters can result in poor adhesion, which in turn, may need re-sanding and a touch up.

Can Rust Bullet be used instead of Standard Military Paint?

Rust Bullet has strong resistance to chemicals and abrasives in addition to its superior patented technologies for controlling rust and corrosion. Rust Bullet more than qualifies as a replacement to the CARC paint system and is a lot easier and safer to handle. Rust Bullet can be easily top coated with the U.S. Army’s standard army green paint. Rust Bullet has been awarded a Schedule Contract with the General Services Administration (GSA), one of the world's largest suppliers of quality products to government buyers. Due to the versatility of Rust Bullet, the GSA has listed Rust Bullet under, not one, but four Special Item Numbers (SIN). A SIN is a category for the functionality of a product. Rust Bullet can be obtained by United States Government Customers directly from Rust Bullet, LLC (now listed as a GSA Schedule Contractor), or through the GSA Advantage!® Online Shopping and Ordering System using the URL: http://www.gsaadvantage.gov. To purchase Rust Bullet through GSA Advantage! enter Rust Bullet in the search feature of the GSA Advantage! Catalog. 1.Rust Bullet GSA Contract Number: GS-06F-0050R 2. GSA Schedule Number: 51V 3. Rust Bullet Cage Code: 3E9H7 Some of the United States Government Military and Non Military Agencies currently using Rust Bullet: 1. Federal Aviation Administration, (FAA) 2. United States Department of Transportation, (DOT) 3. United States Navy 4. United States Army 5. United States Marine Corps 6. United States Naval Undersea Warfare Centers 7. The National Radio Astronomy Observatory's Very Large Array (VLA), one of the world’s premier astronomical radio observatories

Can Rust Bullet be Top Coated?

Rust Bullet is metallic gray in color and requires no topcoat. If a finished color other than metallic gray is desired, Rust Bullet can be top coated between 24 to 48 hours after the final coat has been applied. Rust Bullet is compatible with most conventional top coat paints. Rust Bullet BlackShell is formulated specifically as the optimum topcoat for both Rust Bullet formulas if a smooth glossy black finish is desired. BlackShell is scratch and chip resistant, UV resistant, as well as, resistant to Acid Splash and Chemical Solvents. BlackShell is an excellent protective stand alone coating, requiring no basecoat or topcoat. BlackShell will easily outperform other protective coatings; however, the unbeatable combination of BlackShell over Rust Bullet or Rust Bullet Automotive will provide the absolute best protection against rust and corrosion available today.

Can BlackShell provide protection for Industrial and Commercial Projects?

Rust Bullet BlackShell can be used on bare steel and will provide very good rust and corrosion protection. BlackShell is formulated with specialized resins and anticorrosive agents and can be used as a stand alone anticorrosive coating that will protect iron and steel. Although BlackShell will easily outperform other coatings on bare steel it will not produce the level of protection of the patented Rust Bullet standard or Rust Bullet Automotive formulas for fighting rust and corrosion. For the absolute best rust and corrosion protection available, apply BlackShell over Rust Bullet standard or Rust Bullet® Automotive.

What is the Recommended Application Method for Galvanized Corrugated Roofs?

The recommended application method for Rust Bullet on Galvanized Corrugated Roof projects is an airless spray system with a 517/519 tip and 2400 PSI. Two or more coats should be applied depending on the desired dft (dry film thickness); each coat of Rust Bullet will add strength and durability to the metal roof. Please refer to our Application Guidelines for detailed instructions on airless spray systems.

Will Rust Bullet Protect a Concrete Shop Floor and Concrete Roof?

Concrete has been a reliable and versatile product for centuries. Chosen for its strength and durability, concrete is expected to withstand the most abusive conditions. It is subjected to the destructive effects from harsh chemical spills, abrasive objects, moisture, and the impact from heavy tools and machinery often resulting in an unsightly appearance and damage requiring costly repairs or replacement. Rust Bullet, with its Superior Patented Technology for rust and corrosion control, also provides outstanding protection to many other surfaces, including concrete. Rust Bullet protective coating will: 1. provide excellent chemical resistance 2. provide protection from abrasives 3. seal a surface from moisture 4. allow easy clean up of spills 5. prevent concrete from sweating 6. reduce dust 7. fill cracks, gaps, and chips 8. enhance appearance 9. add years of life to concrete surfaces Rust Bullet is an excellent coating for concrete floors and roofs. To prepare a surface for coating it is necessary to remove all dirt and debris, allowing the surface to fully dry prior to applying Rust Bullet (power wash the surface if possible). Rust Bullet provides protection from everyday abrasives as well as creating a moisture barrier for further protection from oils, water, and chemicals (such as battery acid, hydrochloric acid, and sulfuric acid). Rust Bullet is a self leveling product; therefore, the first coat will fill in cracks, gaps, and chips as it soaks into the concrete. Rust Bullet, with its Superior Patented Technology not only improves the appearance of concrete, it will make concrete stronger and more wear resistant, adding years to its life. A rough or non-skid surface may be achieved on a concrete floor protected with Rust Bullet by applying fine silica blasting sand or regular washed sand. The sand can be applied by hand or by using a drywall hopper/compressor. Start by applying the first coat of Rust Bullet using a roller and then sprinkle the sand on the area. Continue rolling the Rust Bullet and sprinkling the sand until you have completed the first coat and the area is coated with both products. When the Rust Bullet has dried, and will not transfer to a gloved finger, apply a second sealing coat of Rust Bullet. A third coat is highly recommended for heavy traffic areas.

Is Rust Bullet recommended for use on a Chain Link Fence?

Known for its strength and durability, chain-link is perhaps the most economical type of fencing available. Commercial chain-link fence systems have been preferred for decades to define property lines, adding protection, security, and value to homes and farms. Fence manufacturers make products for many different uses including lightweight, temporary needs. The application of Inferior coatings may allow the components to rust prematurely. The result is a permanent installation made from materials that weren't designed for longevity. The protective coating will fail much sooner than loss of steel integrity. Many manufacturers offer warranties that apply only to the loss of structural integrity of the steel, meaning the product has rusted to the point that the strength of the steel is no longer there. Rust Bullet Standard Formula (Gold Label) will provide superior protection from corrosion and abrasives to chain-link fencing adding years of life to the integrity of the steel. Prior to applying Rust Bullet, simply wire brush the rusted areas to remove loose or flaking rust; wash off dirt and dust and let fence dry completely. The best tool for application to the chain mesh is a long-nap paint roller with a 1 1/2-inch nap; the longer the nap the better because the roller's fibers will reach through and around the fence material. Ideally both sides of the fence can be coated at the same time with the assistance of a co-worker. A brush should be used on the fence rails, posts, hardware, and horizontal supports. If an airless spray system is used a 517 tip size is recommended. It is important that the area behind the fence be protected from overspray.

Can Rust Bullet be used for Wrought Iron Fencing, Furniture, and Fixtures?

Rust Bullet Standard Formula (Gold Label) will provide superior protection from corrosion and abrasives to wrought iron fencing, furniture, and fixtures, adding years of life to the integrity of the steel. Prior to applying Rust Bullet, simply wire brush the rusted areas to remove loose or flaking rust; wash off any dirt and dust or oil film and let the surface dry completely. The best methods of application for wrought iron are a Close Nap Roller or an Airless Spray System; paint brush application will also work. Less expensive sprayers, such as a Wagner Power Sprayer, can be purchased for home use. Prior to using spray equipment, be sure to run Xylene or Toluene through the equipment to remove any moisture. Please see our Application Information and Guidelines for more detailed information on spray application. If black is the desired finished color for the wrought iron, use Rust Bullet BlackShell as a topcoat. BlackShell is formulated with specialized resins and anticorrosive agents and can be used as a stand alone anticorrosive coating that will protect iron and steel. Although BlackShell will easily out-perform other protective coatings, it will not produce the level of protection of the patented Rust Bullet standard or Rust Bullet Automotive formulas for fighting rust and corrosion. For a black finish with the absolute best rust and corrosion protection, apply BlackShell over Rust Bullet® standard or Rust Bullet Automotive.

Is Rust Bullet an appropriate coating for use on an Air Duct?

Rust Bullet will provide excellent protection for an Air Duct System. We recommend not running air through the system for 72 hours after the final coat of Rust Bullet has been applied. Rust Bullet will encapsulate the rusted areas adding strength to the coated surfaces.

Can Rust Bullet be Applied to Stock Drinking Tanks?

Rust Bullet has not been approved as a coating for containers for food or water consumption by the Food and Drug Administration (FDA); however, Potted Water and Volatile Organics Tests performed at Great Basin Laboratories, Inc. confirm Rust Bullet Coating meets the EPA and state of Nevada’s Primary and Secondary Drinking Water Standards. Water held in a container coated with Rust Bullet was tested for potability after 30 days and then again after 120 days and met the United States Environmental Protection Agency's (EPA) primary and secondary drinking water standards.

How does Rust Bullet Hold up to Diesel Fuel?

Rust Bullet will hold up to diesel fuel No.2 with no adverse effects. Scuffing the surface prior to applying Rust Bullet would provide increased adhesion as opposed to just recoating within the recommended timeline. Rust Bullet will provide a chemical bond to the metal and the topcoat when properly.

Is it necessary to remove Existing Surface Paint prior to the application of Rust Bullet?

The removal of existing surface paint prior to Rust Bullet application will depend on the condition and type of paint on the surface. To achieve maximum adhesion, it is always recommended to remove any old paint or coating before applying Rust Bullet.

Do I Apply Rust Bullet only where Rust is Apparent?

Rust Bullet is designed to protect rusted and clean metal. It is always advantageous to protect metal, even when there are no visible signs of corrosion. If Rust Bullet is applied only in the rusted areas, it will stop the rust on that surface area, but the uncoated area will be left unprotected. Remember, if it’s made or iron or steel, it will rust and corrode if left unprotected.

How many coats of Rust Bullet are required for my project?

Rust Bullet requires a 6 – 12 mil dry film thickness (dft) for Home and Farm applications. This requirement will vary depending upon the type of application. The higher the mil measurement of Rust Bullet's dft, the greater the protection provided. Many variables should be considered when determining the desired dft for any project. Some of these variables to consider are: 1. The existing condition of the surface being coated 2. The surface’s exposure to: 3. Moisture 4. Harsh chemicals 5. Abrasive objects 6. The damaging effects the surface must endure from environmental conditions As Rust Bullet cures, it releases carbon dioxide gas while dehydrating the rust. This process may create small pin holes in the first coat of Rust Bullet. The second and successive coats will seal these tiny pin holes and form an air tight, armor like shield over the application surface. If these pin holes are not sealed after the first coat, air and moisture may penetrate the Rust Bullet, allowing rust and corrosion to form.

Can Rust Bullet be Top Coated?

Rust Bullet is metallic gray in color and requires no topcoat. If a finished color other than metallic gray is desired, Rust Bullet can be top coated between 24 to 48 hours after the final coat has been applied. Rust Bullet is compatible with most conventional top coat paints. Rust Bullet BlackShell is formulated specifically as the optimum topcoat for both Rust Bullet formulas if a smooth glossy black finish is desired. BlackShell is scratch and chip resistant, UV resistant, as well as, resistant to Acid Splash and Chemical Solvents. BlackShell is an excellent protective stand alone coating, requiring no basecoat or topcoat. BlackShell will easily outperform other protective coatings; however, the unbeatable combination of BlackShell over Rust Bullet or Rust Bullet Automotive will provide the absolute best protection against rust and corrosion available today.

Can BlackShell provide protection for Home and Farm Projects?

Rust Bullet BlackShell can be used on bare steel and will provide very good rust and corrosion protection. BlackShell is formulated with specialized resins and anticorrosive agents and can be used as a standalone anticorrosive coating that will protect iron and steel. Although BlackShell will easily out-perform other coatings on bare steel it will not produce the level of protection of the patented Rust Bullet standard or Rust Bullet Automotive formulas for fighting rust and corrosion. For the absolute best rust and corrosion protection available, apply BlackShell over Rust Bullet® standard or Rust Bullet Automotive.

Will Rust Bullet have an effect on Rubber CV Boots , Rubber Seals etc?

As Rust Bullet Products form an armor tuff non-porous finish, the coating will have the same influence on rubber surfaces as on all other surfaces. Rust Bullet is a moisture cured product that will dehydrate the rubber (absorb the moisture) thereby reducing flexibility. To prevent Rust Bullet Products from adhering to the rubber surface, apply an oil based lubricant (i.e. rubber lube) to the rubber using a towel or cloth. Do not use a spray lubricant. Apply with caution to prevent the lubricant from coming into contact with the surface to be coated with a Rust Bullet Product as the lubricant will interfere with the adhesion process. This will enable you to wipe off any overspray easily.

Can steel and alloy suffer from galvanic reaction where the two are joined?

Rust bullet will prevent the chemical action between the two metals and has phenomenal adhesion which will bond easily to both the aluminium and steel.

What is Rust and How does it Form?

Rust is a reddish-brown oxide coating formed on iron or steel by the action of oxygen and moisture. Rust occurs when things made from iron are exposed to damp conditions and the iron gets reddish brown flakes on it. 1. Rust happens when iron, water and oxygen mix together. This is called oxidation. 2. Rust is a chemical reaction that creates a new substance called Iron Oxide. 3. The oxidation weakens the metal allowing it to break much easier. Rust is the chemical combination of iron with oxygen. It's an example of a very common and very important type of chemical change: OXIDATION, the combining of a material with oxygen. (There is a second meaning of oxidation which is broader and includes reactions that don't involve oxygen.) Rust happens quite naturally, when iron contacts air. The air is about 1/5 oxygen gas. When a car is "rust-proofed" it is coated with a substance so that the oxygen in the air can't reach the iron. Take a look at an older car that has scratches on it. See how the red rust forms in the scratches, where the air can get at the metal? You can speed up the rusting process by heating the iron, or adding water or saltwater. If you'd like to make rust, just leave an iron nail or piece of sheet iron in a jar of water or saltwater. Pretty soon the surface will be coated with a red flakey compound: iron oxide, or rust. This falls off and exposes the next layer of iron to the air, and the iron will continue to rust. Almost all metals oxidize, and form OXIDES (compounds with oxygen). But not all metals form weak flakey compounds when they oxidize. For example, aluminum forms a very strong compound called aluminum oxide. This aluminum oxide forms a tough "skin" on the surface of the aluminum, preventing air from reaching the inner layers of metal. So the aluminum is protected from the air by its "rust" or oxide. A recently released two-year breakthrough study estimates the annual direct cost of corrosion in the United States to be $276 billion. While this is a sizeable number, larger than many of the world's economies, it has been estimated that 25-30% of the total, or $70-80 billion, could be saved by using state-of-the-art corrosion management practices. In addition to the cost savings, corrosion can result in public and industrial safety issues. Rust has been a problem which humanity has been fighting since the dawn of the Iron Age. If it is made of iron or steel, it will rust and corrode if left unprotected. Although various prevention strategies have been discovered and developed, they all had flaws and short comings that limited their usefulness. They were either very complicated to apply, required multiple steps with a highly trained work force and ideal working conditions, or they were simple to apply but didn’t work very well or last very long. Keeping this in mind, a scientific research team was brought together to solve this age old problem. After three years of extensive scientific testing, we developed a simple, easy to apply, rust/corrosion control product that is more effective on both clean metal and rusty metal than any other (in the field use) product on the market. Because this formula had such phenomenal results, we decided to bring it to market, calling it Rust Bullet®. IT KILLS RUST!

Corrosion Control Products:

There are several hundred corrosion control products manufactured around the world, each one with it's own advantages and disadvantages. For the consumer client the most important factor is cost. The cheaper the product the more interest is generated. However, if the cheap product worked, you would not be reading about Rust Bullet Products. The fact is corrosion control is not a simple ABC process. Rust Bullet Products are unique in that they do not require intricate, complicated and time consuming surface preparation prior to application. Our Products are simple to apply which means saving money and manpower. Many inexpensive corrosion products have many hidden costs and end up more expensive as they require extensive preparation and then require UV Protective coatings, and that cost money, labor and time. Additionally many of these products also offer no warranty, unlike Rust Bullet. Rust Bullet Products have been extensively tested and exceed all the international standards required of a corrosion product. Consumers using Rust Bullet Products enjoy longevity of their assets. Equipment and vehicles last longer and structures show less wear. Rust Bullet protects your investment and the environment in which we live. More equipment in our world is destroyed by rust and corrosion than any other element.

What is the Difference between a Rust Converter and a Rust Inhibitive Coating?

A Rust Converter changes the composition of rust into another form of Iron which over time also will rust. Rust Bullet does not convert rust. It does not alter or change rust into something else. Rust Bullet killls rust by dehydrating the moisture out of rust then expelling the moisture through its pores using our Patented New Technology. Rust can not thrive without moisture. That’s why with our air tight armor like coating, Rust Bullet is the only rust inhibitor in the Industry to make this statement. When Rust Bullet is properly applied it comes with a 10 year warranty. No other product can stand by such a statement.

The Birth of Rust Bullet:

The Birth Place of Rust Bullet lies with our own government. Rust Bullet was originally designed to go onto the wing tips of military Jet Fighters that reached speeds well over Mach - 2 (twice the speed of sound) Rust Bullet protected the wing tips from severe corrosion, chipping, and other damage involved from maneuvers in a high speed environment.

How Do Rust Bullet Products Kill Rust?

Rust Bullet product completely dehydrates the rust through a dual patented process. In effect completely eliminating as well as encapsulating the rusted areas armor like coating which will add strength and durability to the rusted area. properly applied Rust Bullet comes with a 10 year Warranty. Depending upon application it may be as little as a two to three coat application equaling a total thickness of 6 mils that is required. Rust Bullet is a moisture cured Product dehydrates the rust and expels the dehydrated gases through its pores. This takes many hours. Humidity will excel the process. Only pour out what you can an hour or so. Never pour unused Rust Bullet back into the original container.

How Good Is Rust Bullet?

Rust Bullet® is such a versatile product that there are countless applications. We at Rust Bullet LLC are constantly being amazed at the ingenuity of our customers by the variety of uses to which they put our products. Rust Bullet is a One Step Two Coat Moisture Cured Urethane Based Patented Product that penetrates through and dehydrates the rust, sealing the surface area with armor like coating. When properly applied Rust Bullet will protect the treated area for at least 10 years. Rust Bullet® is a super-tough, high-performance; Industrial grade rust inhibitive coating that can be applied directly over rusty or clean surfaces providing permanent rust protection with phenomenal adhesion. Rust Bullet® is very resistant to Acid Splash and Chemical Solvents it Protects Iron, Steel, Galvanized Aluminum, and Sheet Metal to name a few surfaces. Rust Bullet® not only provides excellent protection for Concrete Floors and Leaking Concrete Roofs, it Protects Wood, and Fiberglass. Our products have been used to treat surfaces such as; Trailers, Asphalt Surfaces, Parking Lots, Tennis Courts, Automobiles, Ships, Trains, Roofs, Oil Refineries, Waste Water Treatment Plants, Decorative Ironwork, to name a few.

Why Doesn't Rust Bullet Come in Colors?

Here at Rust Bullet we feel it's to everyone's best interest not to color our product. Any time a product in our field is colorized something has to be given up. That one thing is Durability which we do not choose to give up. Colorizing a product such as ours would drastically reduce the long lasting staying power of the product by approximately 40%. That’s why Rust Bullet is one of the only products in our classification that offers a 10 year warranty. We will not compromise quality for color. Rust bullet is metallic grey in color and will accept a top coat of your choice if colorizing is desired. We now have Rust Bullet BlackShell Gloss Black available. It is just about as tuff and durable as our regular Rust Bullet product. BlackShell is scratch and chip resistant, UV resistant, and also resistant to Acid Splash and Chemical Solvents.

What is the PH of rust bullet?

Slightly Acidic

Galvanic Corrosion between Two Dissimilar Metals:

Rust Bullet will prevent the chemical action between the two metals.

What is the Temperature Range for Applying Rust Bullet?

Optimum temperature range to apply Rust Bullet® is 35°F (2°C) to 110°F (43°C). Never apply Rust Bullet® while raining or under threat of rain.

What is the Shelf Life of Rust Bullet Products?

Shelf life of unopened containers is approximately two years. Opened containers shelf life is approximately 3- 4 Months. The storage ranges are: A low of 33 Degrees to a High of 120 Degrees. Rust Bullet is a specialized moisture cured product. Containers that have been opened should be used up in a few months. A protective element, heavier than air, is added on top of Rust Bullet Products at the factory. It escapes from the can when the lid is removed exposing the contents to the outside atmosphere. Humidity will also affect any open container Rust Bullet should not be exposed to the outside air for any length of time. Pour out what you intend to use and put the lid back on right away. For best results only pour out what you intend to use up in about an hour or so. Put the lid right back on the can as soon as you pour out what you need to use. Never pour any unused product back into the original container as this may cause contamination.

What is the Difference between a Rust Converter and a Rust Inhibitive Coating?

A Rust Converter changes the composition of rust into another form of Iron which over time also will rust. Rust Bullet does not convert rust. It does not alter or change rust into something else. Rust Bullet killls rust by dehydrating the moisture out of rust then expelling the moisture through its pores using our Patented New Technology. Rust can not thrive without moisture. That’s why with our air tight armor like coating, Rust Bullet is the only rust inhibitor in the Industry to make this statement. When Rust Bullet is properly applied it comes with a 10 year warranty. No other product can stand by such a statement.

Do Rust Bullet Products Contain Lead or other Harmful Elements?

Rust Bullet contains no zinc, no chromates, no acids, and no heavy Metals, and complies with Volatile Organic Compound (VOC) limits regulated by The Environmental Protection Agency and the more stringent regulations of the State of California. Rust Bullet is DOT unregulated on the ground shipment.

Galvanic Corrosion between Two Dissimilar Metals:

Rust Bullet will prevent the chemical action between the two metals.

What topcoat can be used on Rust Bullet

Rust Bullet requires no topcoat however the final coat of Rust Bullet can be top coated after 24 hours with most conventional topcoat paints compatible with aluminium surfaces , due to the large number of coatings available it is recommended to check manufactures guidelines and use the appropriate primer where recommended for a particular topcoat. Water based or latex paints are not recommended to be applied directly to Rust Bullet.

What topcoat can be used on Rust Bullet

Rust Bullet requires no topcoat however the final coat of Rust Bullet can be top coated after 24 hours with most conventional topcoat paints compatible with aluminium surfaces , due to the large number of coatings available it is recommended to check manufactures guidelines and use the appropriate primer where recommended for a particular topcoat. Water based or latex paints are not recommended to be applied directly to Rust Bullet.

What topcoat can be used on Rust Bullet

Rust Bullet requires no topcoat however the final coat of Rust Bullet can be top coated after 24 hours with most conventional topcoat paints compatible with aluminium surfaces , due to the large number of coatings available it is recommended to check manufactures guidelines and use the appropriate primer where recommended for a particular topcoat. Water based or latex paints are not recommended to be applied directly to Rust Bullet.

Do you have a technical / engineering data sheet?

Yes please follow this link to the US site: http://www.rustbullet.com/uploads/RBAEngData0210.pdf

Is there a Technical Data Sheet for RustFormulaX?

RustFormulaX TECHNICAL DATA SHEET. 1. IDENTIFICATION OF PRODUCT AND COMPANY 1.1 Product name : RustFormulaX Water based rust converter / primer 1.2 Company: Rust Bullet Limited 31 Straight Road Boxted Colchester CO4 5HN Tel 07909 517395 Website: www.rustbulletuk.com 2. TECHNICAL DATA 2.1 STORAGE: Protect from freezing. 2.2 APPLICATION: Apply one or two coats by spray, brush or roller. 2.3 OVERCOATING: 8 hours if overcoating with a water based product. Allow a minimum of 24 hours if overcoating with solvent based materials. 2.4 DRYING TIME: 2 to 4 hours, very dependent on the drying conditions. Full reaction time 24 hours. 2.5 COVERAGE: Theoretical - up to 12 sq. Metres per litre. Practical - 8 - 10 sq. Metres per litre. 2.6 PACK SIZE: 5 litres 2.7 DRY FILM: 25 microns. 2.8 FLASH POINT: None. 2.9 FIRE RESISTANCE: Tested to Class “O” BS 476 Parts 6 & 7 - Passed 2.10 TOXICITY: Non toxic. Approved for use in food and drinks manufacturing plants by Departments of Agriculture for Canada and The United States 3. PREPARATION 3.1 RustFormulaX is supplied ready to use. Stir well before use. DO NOT THIN. 3.2 When using RustFormulaX, always decant into a separate container and never return surplus material to the original container. 3.3 Surfaces should be clean and free from surface dirt, dust and grease. Light to medium rusted steelwork must be properly prepared by wire brush or power tools (SSPC.SP3) to remove loose millscale and flaky rust and paint, which is not sound or tightly adhered. 3.4 Weathered steel should be high pressure water or wet abrasive blasted to SSOC-SP6. 3.5 Best results are achieved if some bright metal (10%) is showing in the rusted area. 3.6 Apply RustFormulaX when the humidity is greater than 40%. 3.7 On warmer days it is recommended to damp down warm steel with a mist of water prior to application. 4. APPLICATION 4.1 RustFormulaX should be stored at room temperature (20oC/68oF) for 24 hours before use. Best applied by brush or deck scrubber to encourage penetration of rusted surfaces, but RustFormulaX can also be applied by spray or roller. 4.2 Apply RustFormulaX when the air and surface temperatures are between 5oC and 30oC and the relative humidity between 40-90%. 4.3 Thin, even coats applied by brush are the preferred method of application. Brush RustFormulaX well into the rust to leave a dry film thickness of 25-30 microns. 4.4 RustFormulaX in the wet state is off white in colour. The changing colour of the coating indicates that the chemical reaction is taking place. After treatment with RustFormulaX, the overall area should be navy/black in appearance. If this is not the case, insufficient surface preparation has been carried out. 4.5 RustFormulaX will normally be touch dry within 2 hours depending on the temperature and humidity. Cooler temperatures delay curing. Allow a minimum of 8 hours before overcoating with water based products and 24 hours with solvent based topcoats. 4.6 Wash brushes and equipment with water immediately after use. Clean spray lines before RustFormulaX dries. Once dry, RustFormulaX is difficult to remove. Use an aromatic solvent to soften dry brushes or free clogged lines. 5. HEALTH AND SAFETY These products are considered to be non hazardous. However, please ensure that operators read and understand the health and safety data sheet before using these materials. Revised May 2009